Maintenance%20Tips-%20Round%20Baitcasting%20Reels%20(2%20pages).

Maintenance%20Tips-%20Round%20Baitcasting%20Reels%20(2%20pages)., Fishing, Smarowanie i koserwacja ...

[ Pobierz całość w formacie PDF ]
Maintenance Tips– Round Baitcasting
Reels
Shimano®
reels, when properly maintained, provide years of dependable high performance. Below are a few
simple steps to help keep your Shimano® reels in top condition, as well as, preventative measures to avoid costly
repairs.
List of tools that may be needed for service:
Tools
: Small Flat Head Screwdriver, Small Phillips Head Screwdriver , 10MM Nut Driver or Shimano®
Wrench
Lubricants:
Shimano® Bantam™ Oil (BNT1445), Shimano
Drag Grease (A-DRA1/4)
Cleaners:
Cotton Swabs, Isopropyl Rubbing Alcohol, Tooth Brush, Paper Towels or Rags
Schematics:
All Shimano® reels come with schematics, however, they can also be found here:
Tools and cleaning materials rec-
ommended to service reel. Some
Shimano® reels come with Ban-
tam™ Oil.
These simple tools are
readily available at hardware
stores.
Access the spool assembly on Shi-
mano® Calcutta® and Calcutta B®
via thumbscrews located on right side
plate. Remove spool assembly
Using cotton swabs and/or a
toothbrush with isopropyl rubbing
alcohol, clean the exterior of the
reel.
Clean levelwind system of dirt,
debris and old grease. Apply 3
drops of Shimano® Bantam® Oil
to levelwind. On heavily used
reels, Shimano® Drag Grease may
used also be used.
Inspect and clean spool assembly.
Check spool shaft bearing or bush-
ing for rust, corrosion or damage.
Apply only 1 drop of Shimano ®
Bantam® Oil to spool shaft bear-
ing or bushing.
Clean and oil VBS® Brake Collars
to maintain optimal casting per-
formance. Inspect collars for wear
and tear; replace accordingly.
Remove Cast Control Cap. Inspect
bearing, spring and O-ring for wear
and tear. Clean Cast Control Cap
and apply 1 drop of oil.
We recommend using only
1
drop
of oil on the spool bearing. Excess
oil will find its way into the drag
system, adversely affecting its per-
formance.
Important note
:
When reinstalling
Right Side Plate onto reel, please
make sure that the Thumb Bar is
held in the “up” position. Other-
wise, the clutch will not work.
1
Heavy Duty Maintenance:
Recommended for reels that have had extensive saltwater exposure and/or
those that have been submerged in saltwater.
Lightly rinse reels with freshwater using a spray bottle. Avoid excessive water from a high pressure source as this
may push salt and/or debris inside the reel. Wipe down reel with a rag or towel after rinsing. This is also good
practice after every fishing trip.
Begin by removing handle assem-
bly using small screwdriver. There-
after, remove handle nut with
10mm nut driver.
Remove star drag and drag spring
washers. Note the order in which
the washers are assembled to en-
sure proper reassembly.
After removal of right side plate
screws, remove right side plate.
Remove yoke springs, pinion gear,
yoke and drive gear with drag
washers.
Clean parts with isopropyl rubbing
alcohol using a toothbrush and/or
cotton swabs.
Use Shimano® Drag Grease to
lubricate drive gear. Fill the threads
half way around with grease.
Order of drag washers: Carbon (big
hole), metal (keyed), carbon , metal
(eared), carbon and thick metal key
Lightly
grease drag washers. Too
much grease will reduce the maxi-
mum amount of grease that the reel
will produce.
Reinstall drag washer one by one
to make sure that they all go in
place properly. Handle drag wash-
ers with care!
Thin Spring Washers
Thick Spring Washers
Reinstall yoke, pinion gear, yoke
springs and roller clutch inner tube.
Reinstall right side plate and right
side plate screws. Make sure that
the drag spring washers and spacer
are in the correct order:
Reinstall star drag, friction washer,
handle assembly, handle nut and
handle lock plate.
2
[ Pobierz całość w formacie PDF ]

zanotowane.pl

doc.pisz.pl

pdf.pisz.pl

mement.xlx.pl